Quantcast
Jump to content

Recommended Posts

Posted

We do use Snap-On equipment and some Bosch scanners. The aftermarket tools are definitely getting better, but the factory tools are still the best. The difference is not so much in the engine management areas where much of the info is mandated by the EPA, but we see more holes in airbags, body control modules, HVAC controls, VSC, ABS etc. Many of the OE's have made there tools and subscription much more affordable. Initial software purchase seems to be $3,000 to $4,000 per manufacturer. Most domestic and Asian platforms will run $1,000 to $2,000 per year for subscriptions to the manufacturers site for reprogramming etc. We put several makes on 1 laptop to save some hardware cost.

Posted

I am leaning more towards OEM scanners. Haven't bought one YET but I believe its headed that way. I find a lot that I cant do because of the limitations of my snappy scanner. Have been looking at the Launch. If it does all it says it will then a factory tool may not be necessary. The real factor is at what cost do we equip the shop to cover "everthing"? Selling the test time is tough. Now do you raise your test rates to cover the added expense OR will the factory tool make the test so much easier that it would improve the test time. Would you have a tech trained on each tool or all trained on every tool? Going from a DRB to a STAR SCAN to a TECH2 could cause a bit of a drag as each tool works differently. The expense along with the updates makes it very costly!

Launch is absolute junk. Slow and almost unusable. At least from my experiences.

 

Sent from my SCH-I605 using Tapatalk 2

 

 

Posted

OE is the way to go. Only use generic (snap-on, autel etc) in order to get a quick look at what’s going on then switch to the OE tool if need be. We have multiple lines OE and they have become more reasonable to afford.

Posted

I have 12 scanners right now. Half are manufacturer scanners. What I can do with the manufacturer scanners far exceeds any of the aftermarket ones.

 

The big issue is, that I tend to forget what is available on one and not on another. Old age I guess. LOL

I have found some of the diagnostic steps tend to be written for info that is only found on the manufacturers scanners. Although there are times when the type of info is put into different terms from one scanner to the next.

 

Example, if you were looking for the exact voltage on a Chrysler 3 wire A/C transducer the factory scanner has it but you have to dig around to find it, but the Master tech pops it up very quickly... and in volts not in resistance values. (At least the last time I look for it) Then there are the times I'm programming something and I'll use an aftermarket scanner and the dang thing will get you right up to the very last step and then leave ya stranded. (hate that)

 

All in all, until such time as the aftermarket gets it together and has ALL info for one vehicle the manufacture level scanner still has them beat.

 

I figure when some of these models get older all that info will be out there for the aftermarket scanner builders, because... the manufacturer will have moved onto a new more sophisticated scanner and won't care who's fixing their older models.

Posted

Perhaps we could connect the dots in this thread, with the thread about aftermarket parts not being up to par, and come to the conclusion aftermarket is cheap. Or that you get what you pay for. :rolleyes:

Posted

mmotley,

I'm not ready to agree with that conclusion ...yet.

I do believe that you get what you pay for, but there are many aftermarket parts that I find superior to OE parts. We've replaced many OE wheel bearings, ball joints and tie rods at very low mileage. We use NAPA Adaptive One brake pads and get longer life out of them than the OE pads.

  • 1 month later...
Posted

I ha a snap on verdict. Horrible. Snappy wants me to upgrade to a verus. I have a ford ids. Should I be going most oe scan tools. Has anyone ran into the need of tools for direct injection engines?

Posted

I ha a snap on verdict. Horrible. Snappy wants me to upgrade to a verus. I have a ford ids. Should I be going most oe scan tools. Has anyone ran into the need of tools for direct injection engines?

I've got an old modis that's been upgraded regularly and does everything I need except for flash capabilities. No need for a diesel specific tool unless you specialize in heavy diesel.

 

Sent from my SCH-I605 using Tapatalk 2

 

 

Posted

So far the snap on verus pro is good. But I am not buying unless snap on buys back my awful verdict. The modis only comes with a 2 channel scope now.

Posted

I agree that factory scan tools are the best. With that said I own an Autel scanner which is fully updated and a 4 channel OTC lab scope. I also have a smoke machine. I can pull codes from all modules on pretty much any car and use identifix to get a testing procedure. Most anything that a factory scanner can do can be done with a scope. It takes longer and requires more effort for sure but we can test pretty much anything. Flashing new computers or modules is one thing we can't err don't want to do. The amount of money we lose by sending cars to a dealer for programming new computers is so minimal it's not worth investing in all the different scanners and investing the time to master each one. Don't get me wrong I get frustrated knowing I don't have the best tool for the job sometimes but investing in other areas nets a much greater return on investment.

Posted (edited)

I can honestly say that I am thoroughly disappointed / disgusted with Strap-On and other brands as they all have Huge holes / gaps in them.
The Verus DSO/DVM is a real bad joke. Utterly useless for measuring Mv and negative voltages. (reverse polarity)
Has anyone tried to measure a distributor with 3 hall effect sensors in it with this pos?
I have a '88 Toyota Soarer with a 1G-GTEU 2.0 Twin Turbo (Yamaha engine) in my shop now that I am tracking down no injector pulse... It was made for the Jap market; It is Not a North American vehicle by any stretch of the imagination and information for this beast is virtually non-existent. Nothing in this car ever came over here.
Even the Dealer said "Good Luck!" when I asked about parts availability.

I have learned that if you want true diagnostic capabilities you need to piece together OE tools with high quality dedicated specialty tools.

All-In-One tools leave much to be desired and often are a huge waste of money.

Despite the mandates for OEM's to 'standardize' and make certain data available, they still hold the keys to the kingdom and are playing a money game that penalizes independents for competing.

The OEM's are regenerating the revenue lost to independents by hammering us with proprietary fees.
i.e.; We are forced to buy special tools to work with their proprietary websites and vehicles in addition to subscription access fees and software & firmware updates.

Sure there are standards and mandate compliance, but anything above generic data access with bidirectional support costs us big time.

Technicians cannot afford to invest in everything that is required and that leaves us footing the bill and wincing every time an over priced piece of equipment heads out of the office to the service bay.

In my area, even the 'Specialty Shops' are still working on everything because families and their friends that are referred have multiple makes and models. The public still expects their trusty mechanic to fix everything and anything.
Case in point: The Toyota Soarer I have to manually trace old school style.
Mind you that I am the poor guy who gets these rejects directly from other shops who throw their hands up.

Edited by rjbradlow
Posted (edited)

I ha a snap on verdict. Horrible. Snappy wants me to upgrade to a verus. I have a ford ids. Should I be going most oe scan tools. Has anyone ran into the need of tools for direct injection engines?

 

I've got an old modis that's been upgraded regularly and does everything I need except for flash capabilities. No need for a diesel specific tool unless you specialize in heavy diesel.

 

Sent from my SCH-I605 using Tapatalk 2

 

Uh -- em -- ncautoshop... FYI:

Ford has a new line of Turbocharged Direct Injection GAS engines called Ecoboost.

They are GDI (Non-Turbo) and GTDI (Turbo) engines.

1.0, 1.5, 1.6, 2.0, & 3.5L -- Only the 2.0 comes GDI & GDTI, the rest are GTDI.

 

Furthermore they are late to the scene as other manufacturers have been direct injecting gas for a long time now.

 

Direct Gas Injection was invented in 1902 for Aircraft engines and later by Bosch for Automotive in 1952...

The 1955 Mercedes-Benz 300SL is the first production sports car to use direct gas injection.

 

http://en.wikipedia.org/wiki/Gasoline_direct_injection

 

http://www.bosch-automotivetechnology.com/en/de/powertrain/powertrain_systems_for_passenger_cars_1/direct_gasoline_injection/direct_gasoline_injection_23.html

 

http://delphi.com/manufacturers/auto/powertrain/gas/ems/gdi/

Edited by rjbradlow
Posted

 

 

Uh -- em -- ncautoshop... FYI:

Ford has a new line of Turbocharged Direct Injection GAS engines called Ecoboost.

They are GDI (Non-Turbo) and GTDI (Turbo) engines.

1.0, 1.5, 1.6, 2.0, & 3.5L -- Only the 2.0 comes GDI & GDTI, the rest are GTDI.

 

Furthermore they are late to the scene as other manufacturers have been direct injecting gas for a long time now.

 

Direct Gas Injection was invented in 1902 for Aircraft engines and later by Bosch for Automotive in 1952...

The 1955 Mercedes-Benz 300SL is the first production sports car to use direct gas injection.

 

http://en.wikipedia.org/wiki/Gasoline_direct_injection

 

http://www.bosch-automotivetechnology.com/en/de/powertrain/powertrain_systems_for_passenger_cars_1/direct_gasoline_injection/direct_gasoline_injection_23.html

 

http://delphi.com/manufacturers/auto/powertrain/gas/ems/gdi/

I understand that however in most cases users are speaking of diesel applications when inquiring on scan tools. My comment still rings true, no need for specific scan tools.

 

Sent from my SCH-I605 using Tapatalk 2

 

 

Posted

We recently purchased a Snap On Solus Ultra. We have an OTC Genisys with System 5.0 as well and the Snap On seems to have much more information than the Genisys. I don't think there are any aftermarket scan tools that don't have some holes in coverage though.....

Posted

We recently purchased a Snap On Solus Ultra.  We have an OTC Genisys with System 5.0 as well and the Snap On seems to have  much more information than the Genisys.  I don't think there are any aftermarket scan tools that don't have some holes in coverage though.....

This leads me to another question. What effects will the right to repair changes make in the scan tool area? The manufacturers obviously want the scan tools with their capabilities to be expensive and stand alone systems, or we would have already seen more laptop/mobile based software and generic interfaces. Maybe we should start a thread on the right to repair issues.

 

Sent from my SCH-I605 using Tapatalk 2

 

 

Posted

I use a snapon solus and it is a good scan tool but I still scatch my head when a 4,000 dollar tool can't even setup a CD player in a cavalier. We had to take it to the dealer to be done.

  • 2 months later...
Posted

A couple of months in and the strap on verus has been good

Snappy bought back my verdict at full price. I got the verus free. I have the ford ids and looking to get more oe scan tools though. Ids is great

Posted

I had a 2004 jaguar x type in today with a door adjar light on the dash. My updated to 13.4 snapon solus would not tell me which door was adjar, almost every other vehicle I am able to get this info out of the scan tool.

 

Would the autel maxidas give this info? Harbor freight had them online for about $899 a month ago. I heard from other shops the autel was more geared for euro makes. Any experience from any members?

Posted

It is tough to stay competitive as a general repair shop with the vehicles that are on the road today. There is tons of new technology in cars and if you don't have a make specific scanner you will always be limited. As for the Autel, it is a pretty neat multi-purpose scanner and definitely has a good amount of functions for Euro makes that is left out on a lot of the other swiss army knife scanners out there.

  • 2 months later...
Posted

We have Verus pro for most of the things we need to do. I think it's a great all around tool especially with the last two updates that made it faster. Sometimes I'm actually surprised at what it can do. I love that I have 4 channels of scope with such great sampling rate even when using all 4 channels. It is pricey.

We also have launch for some of the things snap on didn't do before but now it's catching up fast.

We have bow gt1 and Mercedes star 3. For gm if we need something that we can't do with Verus we use passthru J2534 and subscribe for whatever time we need it for. Same with some other manufacturers. I don't see myself switching to all oem any time soon.

Posted

OE vs. Aftermarket scanners

 

Last week I had an old customer come in with a Jeep that his son had put larger tires on. The speedo was off and he wanted to know if I could reset it. I said sure. I tried my Mastertech on it, mainly because that year car (a 99') is what I use to set the pinion factor and VIN when I change out the PCM's. Well, well... wouldn't ya know it. It would not allow me to change the pinion factor because I wasn't changing the PCM. Seems the scanner is only set up to change it if I change the PCM. Kinda ticked me off. Had to go back and get the DRB.

 

Grrrr. Another situation where the aftermarket scanner isn't up to par with the manufacturers scanner. Lesson learned.

And yes... I tried several times to do it, I could see the pinion factor, but it wouldn't allow me to change it no matter what button (or choice of &*%$ words) I tried. I'm hoping it was just me and I missed a step somewhere...but I doubt. Anybody else run across this problem?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Available Subscriptions

  • Have you checked out Joe's Latest Blog?

         0 comments
      The Technician Shortage Is Our Fault, And It's Time We Own It
      Nearly every day, I hear shop owners complain: "There's a technician shortage. We can't find qualified people. There's no one out there." If that's true, then who's to blame?
      The industry? The schools? The government? I don't know how you feel, but who promised us an endless supply of qualified technicians?
      Another common complaint is that young people do not want to work in the trades. Well, if that were true, then why are other trades such as HVAC, electrical, and plumbing growing? What are they doing that the automotive industry is not? 
      Here's the reality we need to face: We do have a problem, but we shouldn't look for someone or any entity to rescue us. Not the government. Not the trade schools. Not the recruiting companies. No one owes us a workforce. If we want great people in our industry, it's up to us. At some point, we need to own up to the truth: Building a pipeline of qualified technicians is our responsibility.
      In this blog article, I will break down the key reasons we are in this situation today and what we, as an industry, can do to solve the technician shortage. Are you ready to look in the mirror?
      Have We Pushed Technicians Away?
      Let's take a look at flat-rate pay. True flat rate, which pays a technician only for the hours they produce, is a controversial pay plan that emphasizes high production levels and creates a competitive work environment that, if not properly controlled, can lead to increased mistakes and a decline in morale and team spirit. Additionally, the stress and physical demands placed on technicians as they age are not favorable to long-term employee retention. What do we do with technicians as they grow older into their fifties and begin to slow down? 
      I have heard all the arguments and pros and cons of flat-rate pay, and I am not going to judge any pay plan. Let the facts speak for themselves. True flat rate has changed in most areas around the country and has evolved into a pay plan that gives technicians some pay guarantee.
      Many shop owners have learned that team morale, along with the opportunity to earn income, is important to technicians and to the company's long-term success. But let me ask you: how many technicians have left or been pushed out over the years because of the old flat-rate pay system?
      Another issue is the workplace environment. I remember being grateful to be hired as a young technician at a local repair shop. While very thankful, the work environment was not ideal. The shop owner kept the bay doors open year-round (I am from New York) unless it rained or snowed. He felt that if the bay doors were closed, customers might think we were closed for business. We had no heat and no hot water. Many of the jobs were done outside, year-round,  in all types of weather. The starting pay was minimum wage, with no benefits, sick days, or vacation pay. 
      Now, again, I need to point out that I was truly grateful for the opportunity this shop owner gave me. I learned a lot working there, and the experience was pivotal in my career. But looking back, I wonder how many people were discouraged by these working conditions?
      While the physical demands of the repair workplace are daunting, perhaps even more critical is the culture. Too many of my generation shop owners preached the mindset of "my way or the highway." We were the business owners, after all. We started our companies, took all the risks, and provided jobs. Why shouldn't we be the ones to set the ground rules our way?   
      Many of us found over the years that the "my way or the highway" mentality was a sure way to isolate employees and make them more likely to look over the fence for greener grass. In other words, it led many technicians to seek employment elsewhere, where they felt they could be appreciated and recognized for their hard work. The issue, however, was that there wasn't much green grass around. Disappointment after disappointment, bouncing from repair to repair shop, eventually led to despair. So, I ask you: were workplace conditions a contributing factor in today's technician shortage?
      Another factor that we are all well aware of is the complexity of the modern automobile. When I started, the work was mostly physical, and you were required to master essentially three vehicle models: General Motors, Ford, and Chrysler. Let's fast-forward to today. The evolution of automotive technology, along with the extensive training and tools required, has outpaced the typical technician's pay compensation, with no clear career path. Again, leading to frustration and insecurity about the future.
      Here is the bottom line: people don't leave their job; they leave their experience. We must do a better job. 
      The News Isn't all Bad; Your Next Steps to Fix the Technician Shortage
      To fix the technician shortage, it will take a combined effort from everyone in the automotive industry, particularly automotive shop owners. Shop owners are in the perfect position to make the greatest impact, not only on their businesses but also on the future automotive workforce.
      First, shop owners must become better leaders and understand that their ultimate success is directly dependent on the people they assemble around them. Any shop owner who mistakenly believes they can build an empire solely on their abilities is destined for serious disappointment. Business owners who think like this will eventually plateau. Without the collective contributions from a team of qualified people, your business will stall; it will not continue to grow.
      Create a workplace that attracts top talent: a clean, professional, well-equipped facility designed to support productivity, teamwork, and a career, not just a job. Build a great reputation in your community by getting involved locally. Become the auto repair shop that people take notice of as "the" place to work.
      Next, shop owners must become more financially knowledgeable. Knowing your numbers and what you need to achieve for a strong bottom-line profit is essential to paying technicians the money they need and deserve. Profit will also allow you to compete with other trade industries by providing a benefits package that has real take-home value and security.
      When it comes to culture, this is where the rubber hits the road. People crave recognition, praise, and a sense of purpose. Despite what you hear, people are not just money-motivated. Once people feel secure in their financial situation, retaining and motivating technicians can only be achieved by connecting with them on an emotional level. You cannot show enough appreciation. Give out praise for a job well done as if your business depended on it, because it does.
      As technicians age, we need to have a place for them. Expecting a 58-year-old to perform like a 35-year-old is unrealistic. We need to be more focused on career pathing. Provide training, skill development, and coaching to develop leaders and mentors within our older workforce. While their bodies may have slowed, the knowledge they have gained is priceless. 
      Our future is dependent on young people entering our industry. We need to give more young people opportunities. Every shop owner across the country should consider hiring an apprentice, then build an apprentice training plan and career path for them. If every shop did this, we could solve the technician shortage within five years. Get involved with the trade schools and high schools in your area. Look into the NAPA Apprenticeship Program. Don't sit on your hands with this one. Do it today.
      Lastly, don't get left behind. Commit to ongoing training for all your employees. Keep up to date with tools and equipment tailored to your business model. Don't try to be all things to all people and all vehicles. Identify your core profile customer and the vehicles they drive, and become an expert on those vehicles and the services you offer.
  • Similar Topics



  • Our Sponsors

×
×
  • Create New...