Quantcast
Jump to content

Restoration for the Mechanic - - - - sometimes it's great to put down the laptop and pickup the wrenches.


Gonzo

Recommended Posts

Restoration for the Mechanic

Electrical issues on today’s cars have certainly taken center stage. Mechanical issues are still there too, but it’s not uncommon to have a mechanical problem be diagnosed, monitored, or calibrated by some electronic means. You just can’t get away from the electrical if you’re in the automotive repair business these days. It’s taken over just about every facet of the automobile.

Today’s mechanics have become something entirely different from the stereotypical mechanic from just a few decades ago. It’s not that long ago when the electrical section of the repair manuals were just a chapter or two, today… its volumes and volumes of schematics and diagnostic procedures. I’m old enough to remember when points and condensers were still the norm, and I’ve watched the industry go from electronic ignition to today’s electronic jungle of wires and processors. We’ve definitely come a long way with the technology.

Even though I work on all these newfangled electrical wizardry systems on the modern car, deep down I’m still the kid who got a kick out of tearing down an old junker and putting it back together. Now, I’m surrounded by modules, proximity keys, and sensors. Occasionally it’s kind of nice just to step away from the computer and just turn a wrench or two. I look forward to those simpler kinds of jobs, the ones that need a craftsman’s touch and not a box of transistors and capacitors to figure out what to do. Back to a time when a driver was more mechanical involved in the process of operating the vehicle. Heating vents with levers and cables, or a hand choke that needed just the right touch to get it started. No electronics, no service light, just the essentials. (For you younger techs, I’m referring to the days when you actually had to unlock a door with a key.)

 

I still marvel at the ingenuity and engineering of those times. I guess it’s one of the reasons why I like going to old car and steam engine shows so much. It’s all about the mechanics for me. Electronics are great, but to see the early mechanical devices that were commonplace a century ago still amazes me. How they figured it out, and how they made it work is shear brilliance. (If you ever get a chance to study some of those early mechanical systems, you might be surprised how things were accomplished prior to the computer age. It’s quite fascinating… well at least to me it is.)

 

It’s great to be able to step back once in a while and just be a mechanic. Back when things were rebuilt and not just replaced with new. There’s a certain satisfaction in taking a broken mechanical device and making it functional again. It’s those jobs that after you’ve wrestled the components into place, and everything is finished you realize that you’re covered in grease, but for some reason you’ve got this big smile on your face. It’s the look of accomplishment, a smile of pride in a job well done.

 

And while you’re cleaning up the tools, you look over at the finished project still smiling, knowing you’re done and can move onto the next project. It just doesn’t compare to finishing up on a modern car when the last thing to do is watch that blue line steadily move across the computer screen, waiting for it to say “Task completed”.

Not that I’m putting down the modern car, no far from it. It’s just nice to take a break once in a while from the technical mumbo-jumbo and just be a mechanic for a change. Even though it’s pretty awesome to solve a difficult electrical issue, it’s hard to beat a good old fashion mechanical repair. For me, when a restoration project shows up at the shop I get a chance to turn off the laptop and open the toolbox. These restoration jobs are just as much for the customer as they are for me. It’s a restoration of some of my old almost forgotten mechanical abilities. (Yea, I still got it…)

 

We put a lot of trust in the modern electronics, something the engineers and designers of those automobiles from a few decades ago never even though of. Their own ingenuity and craftsmanship kept them going. Components were built to be repaired not replaced. I think it’s safe to say that a car from 50 years ago is more likely to start and run in another 50 years but I seriously doubt a car from today would have the same luck. There again, it might be something a technician/mechanic of that era might figure out how to do by then. Me I’ll still stick with being a mechanic/technician … I still like the physical repair aspect of the job.

The future of electronics in today’s cars is constantly changing; sometimes we notice the changes while other times you can’t physically see them. Sometimes all it takes is a little R&R on an old jalopy just to make me remember how far we’ve come. In the meantime, the latest restoration job is done so it’s time to go for a test drive.

 

I’ll get back to the laptop and the modern car world just as soon as I get all the tools cleaned up… it might take a bit though … I’m still admiring the restoration job and I’ve got some more smilin’ to do.

...


View full article

Link to comment
Share on other sites



Great perspective Gonzo. I feel the same way. When an old car comes into the shop, such as 65 Chevy or Buick, I tell the guys, "Don't touch it, leave that one for me". It not only brings me back to my youth when I first started, but it so refreshing at times to work on something that was build in the era "B.C." Before Computers (or before Catalytic converters).

 

Thanks Gonzo for the memories. Always look forward to Saturdays for your articles!

Link to comment
Share on other sites

Gonzo; It's not olny cars from years ago but appliances, clocks, radio's tv's etc, that were made to be repaired back then. You probably remember going to drug stores with your dad to check out a tv vacuum tube! It's were everything is going to and will only get worse, if that's the way you think of it!

Link to comment
Share on other sites

Haha, I'm on the complete opposite end of the spectrum! I see older cars and think "Uh oh, cap & rotor, points, ignition wires... what the heck is a carburetor!?!?!" It is cool to see someone work on these older cars though. No reaching for the scan tool, just pure diagnostics. And like you said, to see how they designed and built some of the things back in those days can be impressive!

 

Great article!

Link to comment
Share on other sites

I've grown up in the electronic age, but it still amazes me seeing all these new vehicles not last past 100k, but a old beater keeps ticking along mile after mile. Do you ever think though, 100 years from now, someone will be writing the same type of article, but about how the electronics of the past (today's technology) were simple to work on and dinosaur technology?

Link to comment
Share on other sites

  • Have you checked out Joe's Latest Blog?

         13 comments
      Most shop owners would agree that the independent auto repair industry has been too cheap for too long regarding its pricing and labor rates. However, can we keep raising our labor rates and prices until we achieve the profit we desire and need? Is it that simple?
      The first step in achieving your required gross and net profit is understanding your numbers and establishing the correct labor and part margins. The next step is to find your business's inefficiencies that impact high production levels.
      Here are a few things to consider. First, do you have the workflow processes in place that is conducive to high production? What about your shop layout? Do you have all the right tools and equipment? Do you have a continuous training program in place? Are technicians waiting to use a particular scanner or waiting to access information from the shop's workstation computer?
      And lastly, are all the estimates written correctly? Is the labor correct for each job? Are you allowing extra time for rust, older vehicles, labor jobs with no parts included, and the fact that many published labor times are wrong? Let's not forget that perhaps the most significant labor loss is not charging enough labor time for testing, electrical work, and other complicated repairs.  
      Once you have determined the correct labor rate and pricing, review your entire operation. Then, tighten up on all those labor leaks and inefficiencies. Improving production and paying close attention to the labor on each job will add much-needed dollars to your bottom line.
  • Similar Topics

    • By Joe Marconi
      As an "old timer" who got his start during the muscle car era, this is hard to accept. Am I too sensitive? 
      The Associated Press covered some of the driveway mechanics and enthusiasts who are converting classic cars into electric restomods.
      This includes some business owners like Sean Moudry, co-owner of InspireEV near Denver. He recently restored a 1965 Ford Mustang with an electric powertrain. The project cost upwards of $100,000.
      Read the article in Ratchet and Wrench:
      https://www.ratchetandwrench.com/site-placement/latest-news/article/11461897/ev-restorations-booming
    • By ASOG Podcast
      The Problem With Bootstrapping A Business
    • By ASOG Podcast
      Maximizing Profits Or Happiness - Is There An Ideal Size For An Auto Repair Shop
    • By TTP

      Premium Member Content 

      This content is hidden to guests, one of the benefits of a paid membership. Please login or register to view this content.

    • By Joe Marconi
      A friend of mine recently purchased a Tesla Model 3. I asked him, "Why?"  He responded, "I don't have to buy gas, and the Tesla requires no maintenance or repairs."
      Oh really? If this is the public perspective of the electric vehicle, they are in for a shock. Yes, a fully electric car does not require gasoline, but they are far from problem-free or maintenance-free. 
      EVs still have tires, steering systems, suspensions, a TON of electronics to repair and reprogram, a complex HVAC system, wheel bearings, differentials, brake systems, cabin filters, wiper blades, require wheel alignments, and on and on and on. 
      Do we need to educate the public? Your opinion? 
       


  • By nptrb, in Automotive Industry,

    By nptrb, in Automotive Industry,

    By nptrb, in Automotive Industry,

  • Our Sponsors



×
×
  • Create New...